New Hampshire NH DMV CDL General Knowledge Practice Test 3
Test 3 of 5. Pick an answer for each question to see if it is right and why; your score appears at the end. You need 40 correct answers to pass, the same ratio as the real New Hampshire test.
- Questions50
- Correct to pass40
- Passing score80%
- Minimum age18 years
-
1. Which components on a typical engine are driven by belts that must be checked for wear and tension?
Show answer
Answer D: The alternator, the water pump and, on many vehicles, the air compressor
Belts drive accessories such as the alternator, the water pump and the air compressor, so one failed belt can take out charging, cooling or air supply.
-
2. At the scale your tractor drive axles are overweight while the trailer axles have room. Sliding the trailer tandems forward will do what?
Show answer
Answer C: Move weight off the drive axles and onto the trailer axles
Sliding the trailer tandems forward brings the rear support closer to the load, so the trailer axles pick up more weight and the drive axles carry less; sliding them rearward does the opposite.
-
3. What do you check about the fire extinguisher during the pre-trip?
Show answer
Answer C: That it is securely mounted, charged and that you know how to operate it
An extinguisher must be held in its bracket, show a charged gauge and be understood by the driver, because a fire leaves no time to learn.
-
4. Why does a cracked frame rail or cross member make a vehicle unsafe?
Show answer
Answer B: The frame carries the whole load, and a crack can spread until the structure fails
The frame is the backbone that supports the body, the load and the running gear, so a crack in it is a structural failure that grows with every mile.
-
5. You can see a crack in a brake drum that runs across more than half the width of the friction surface. What does this mean?
Show answer
Answer C: The drum is defective and must be repaired before the vehicle is driven
Cracks longer than half the width of the friction area mean the drum can break apart under braking heat and must be replaced.
-
6. Before raising the hood to inspect the engine compartment, what should you do?
Show answer
Answer B: Shut off the engine, set the parking brake and chock the wheels if needed
The engine compartment is inspected with the engine off and the vehicle secured so nothing can move or turn while your hands are inside.
-
7. Your speedometer stops working during the pre-trip check. How should it be treated?
Show answer
Answer D: As a defect, because the driver cannot judge and control speed without it
A working speedometer is required equipment, because judging speed by feel in a heavy vehicle is unreliable and speed governs stopping distance.
-
8. A commercial vehicle stops on the shoulder of an undivided two-lane road that carries traffic in both directions. Where do the warning devices go?
Show answer
Answer B: Within 10 feet of the vehicle, plus 100 feet to the front and 100 feet to the rear
On a two-way road the devices must mark the vehicle itself and warn traffic approaching from each direction, and they must be in place within ten minutes.
-
9. Besides allowing the move at all, what does an oversize load permit usually set out?
Show answer
Answer C: The route to be followed, the hours of travel allowed and the warning equipment needed
Permits for oversize movements normally name the roads that may be used, restrict the times of travel, and list the flags, signs and escorts required.
-
10. Why should you never back under a trailer whose landing gear is resting on soft or muddy ground?
Show answer
Answer C: The landing gear can sink or collapse and the trailer can drop or tip over
Soft ground lets the landing gear sink under the load being transferred to it, and a trailer that drops or topples during coupling is extremely dangerous.
-
11. You are the first to arrive at a crash. What is the correct order of actions?
Show answer
Answer C: Protect the area, notify the authorities, care for the injured
Preventing a second crash comes first, because an unprotected scene puts the injured and the helpers in more danger than the original collision.
-
12. How long must the record of a periodic inspection be kept?
Show answer
Answer A: Fourteen months
The periodic inspection report is retained for fourteen months from the date of the report, which covers the full twelve month cycle plus a margin.
-
13. How does a driver keep a vehicle with a manual transmission from rolling back when starting on an upgrade?
Show answer
Answer D: Partly engage the clutch before the right foot leaves the brake, or hold the vehicle with the parking brake until the engine pulls
Something has to hold the vehicle during the instant the foot moves from the brake to the accelerator, and that is either the clutch at its engagement point or the parking brake.
-
14. You are backing into a yard where electrical wires cross overhead. What is the main concern?
Show answer
Answer C: The wires may hang lower than the top of your vehicle
Overhead space has to be checked like any other space around the vehicle, because wires and cables are often lower than they look from the cab.
-
15. For how long is a New Hampshire commercial driver disqualified after a first conviction for driving a commercial motor vehicle with an alcohol concentration of 0.04 or more?
Show answer
Answer B: Not less than one year
RSA 263:94 disqualifies the driver from commercial operation for not less than one year, and for not less than 3 years if hazardous material was being transported at the time.
-
16. After two hours of driving you measure a tire and the pressure reads higher than the cold figure. What should you do?
Show answer
Answer B: Nothing, because pressure rises normally as a tire heats up in use
Air expands as the tire heats, so a higher hot reading is expected, and letting air out leaves the tire underinflated once it cools.
-
17. When speed doubles, what happens to braking distance?
Show answer
Answer D: It becomes roughly four times as long
Braking distance rises with the square of speed, so twice the speed needs about four times the distance to stop.
-
18. What is the basic rule about backing a large vehicle?
Show answer
Answer B: Avoid backing whenever there is another way
Backing is dangerous because you cannot see everything behind you, so the manual tells drivers to plan routes and parking that avoid it.
-
19. The shipper hands you the placards for a load that needs them. Who puts them on the vehicle?
Show answer
Answer C: The driver, who must also make sure they are the correct ones and are readable
The shipper supplies the placards, but it is the driver who must place them on the vehicle and confirm that they match the load and can be read.
-
20. Compared with a fully loaded one, an empty truck under hard braking will often do what?
Show answer
Answer A: Need a longer distance to stop because traction is poor
Stiff suspension and little weight over the tires reduce grip, so the wheels lock early and the vehicle can take longer to stop.
-
21. Which of these is NOT on the federal list of parts and accessories the driver must be satisfied are in good working order before driving?
Show answer
Answer D: The seat cushion upholstery
The federal pre-trip rule names brakes, steering, lights and reflectors, tires, horn, wipers, mirrors, coupling devices, wheels and rims, and emergency equipment; seat upholstery is not on that list.
-
22. A sign before a long descent shows 6 percent. What does that number tell you?
Show answer
Answer A: How steep the grade ahead is
Percent grade is the drop in feet for every hundred feet of road, so the higher the number the faster speed will build and the lower the gear you need.
-
23. You have countersteered to correct a rear-wheel skid and the vehicle straightens out. What must you be ready for next?
Show answer
Answer D: The vehicle may swing back the other way, so you must steer again to correct it
A vehicle coming out of a skid tends to overshoot and swing in the opposite direction, and the driver must be ready to countersteer a second time.
-
24. Why is cargo often covered with a tarp?
Show answer
Answer C: To protect people from spilled cargo and to protect the cargo from weather
A cover keeps material from blowing or spilling onto the road and shields the load from rain and sun; it does not replace securement.
-
25. Which of these is a major cause of skids in heavy vehicles?
Show answer
Answer C: Over-braking, over-steering, over-acceleration or driving too fast for conditions
Skids happen when the tires are asked for more grip than the road can give, which happens through braking, steering or accelerating too hard or simply too much speed.
-
26. You are pulling away from the curb after a delivery. Why is a mirror check needed first?
Show answer
Answer B: A cyclist or a vehicle may be coming up alongside you
Traffic and cyclists can arrive alongside a parked vehicle at any moment, so the mirrors must be checked immediately before pulling out.
-
27. You are about to slow down sharply on a highway to make a turn into a narrow driveway. How can you warn the drivers behind you?
Show answer
Answer C: Tap the brake pedal a few times so the brake lights flash before you slow down
A few light taps flash the brake lights and give following drivers an early warning that you are about to slow or stop.
-
28. What happens to braking distance when speed is doubled?
Show answer
Answer C: It becomes about four times longer
Braking distance grows with the square of speed, so doubling the speed multiplies both the braking distance and the force of an impact by about four.
-
29. Federal rules keep recapped and retreaded tires off the front wheels of which vehicle?
Show answer
Answer B: Any bus carrying passengers
The federal rule names buses: a bus may not run with regrooved, recapped or retreaded tires on its front wheels, because a steer tire failure with passengers aboard takes away steering control.
-
30. What is generally the safest speed in dense but freely moving highway traffic?
Show answer
Answer D: The speed of the traffic around you, up to the posted limit
Crashes rise with the difference between your speed and the traffic around you, so moving with the flow within the legal limit is safest.
-
31. What happens to a New Hampshire commercial driver found operating with any alcohol at all in his or her system?
Show answer
Answer A: The driver is placed out-of-service for 24 hours
RSA 265-A:24 forbids driving a commercial motor vehicle with any alcohol in the driver's system and places that driver, or one who refuses testing, out-of-service for 24 hours.
-
32. How are the headlights, marker lights and turn signals checked during the seven-step inspection?
Show answer
Answer A: The engine is shut off, the parking brake is set, the lights are switched on and then checked from outside the vehicle
The lights are switched on with the vehicle secured, then the driver walks around and confirms each lamp actually works and is clean.
-
33. What are you checking on the mud flaps during the walkaround?
Show answer
Answer C: That they are securely attached, not torn and not dragging on the ground
A flap that is torn or hanging loose stops shielding following traffic from spray and stones, and a dragging flap can catch and tear away on the road.
-
34. You are drifting in the lane, yawning constantly and cannot remember the last few miles. What is the only reliable cure?
Show answer
Answer C: Stopping in a safe place and sleeping
Those are classic drowsiness warning signs, and nothing except sleep repays the sleep the body is missing.
-
35. A delivery van is stopped in the right lane ahead with its flashers on. What should you expect?
Show answer
Answer C: Someone may step into your lane from in front of it
A stopped delivery vehicle hides the space in front of it, and that is exactly where a person carrying a package is likely to walk out.
-
36. You are driving past a park where children are playing close to the curb. What is the correct assumption?
Show answer
Answer A: A child may run into the street without looking
Children act on impulse and do not judge traffic well, so a driver has to expect one to enter the road and slow down in advance.
-
37. An unblocked crate 4 feet long and weighing 900 pounds needs at least how many tiedowns?
Show answer
Answer D: One
An article 5 feet or less in length and 1,100 pounds or less in weight is covered by a minimum of one tiedown.
-
38. How are the extra gears of a multi-speed rear axle or auxiliary transmission usually controlled?
Show answer
Answer D: With a selector knob or switch on the gearshift lever of the main transmission
A range selector on the shift lever lets the driver choose the extra gear range while shifting the main transmission.
-
39. Your vehicle is stopped just past a hill or curve that hides it from approaching traffic. How should the warning devices be adjusted?
Show answer
Answer A: Move the rearmost device farther back, up to 500 feet, so drivers are warned before the obstruction
When a hill or curve blocks the view, the farthest device is moved back beyond the obstruction so approaching drivers see the warning in time.
-
40. How long is a New Hampshire commercial driver disqualified for a first railroad grade crossing violation?
Show answer
Answer D: Not less than 60 days
RSA 265:52-a disqualifies a commercial driver for not less than 60 days for a first railroad grade crossing violation, 120 days for a second within 3 years and one year for a third.
-
41. Rust streaks are running outward from the lug nuts on one wheel. What does this most likely indicate?
Show answer
Answer C: The lug nuts may be loose
Rust trails spreading from the nuts are a classic sign that the nuts have worked loose and the wheel has been moving on the studs.
-
42. A roadside test shows a commercial driver has measurable alcohol in the system but below 0.04. What happens?
Show answer
Answer C: The driver is placed out of service for 24 hours
Any measurable alcohol while on duty results in an immediate 24 hour out of service order, even when the concentration is under the 0.04 limit.
-
43. What is the correct order for a basic double clutch upshift?
Show answer
Answer B: Release the accelerator and push the clutch, shift to neutral, release the clutch, let engine speed drop, push the clutch again and shift to the higher gear
Double clutching passes through neutral with the clutch released so engine speed can drop to match the next gear before it is engaged.
-
44. Why must the driver of a large vehicle keep it centered in its lane?
Show answer
Answer B: The vehicle needs the full width of the lane
A commercial vehicle is close to lane width already, so any drift takes part of the vehicle into the next lane or onto the shoulder.
-
45. Why is a quick lane change particularly risky with a load of hanging meat or of livestock?
Show answer
Answer A: The load swings or leans and can keep pushing the trailer after you straighten out
A swinging or leaning load keeps moving after the vehicle has finished the maneuver, so its momentum acts on the trailer at the worst moment.
-
46. An automatic transmission is left in its normal drive position as the vehicle rolls down a long grade. What does it tend to do?
Show answer
Answer A: Shift up as road speed rises, so engine braking falls away
An automatic left in drive keeps upshifting as speed builds, which is the opposite of what you want on a grade; that is why the driver must select a low range.
-
47. Why is backing toward the driver side preferred?
Show answer
Answer C: You can watch the rear of the vehicle directly through the side window
Backing to the left lets the driver look out the window and see the rear of the vehicle directly instead of relying on a mirror alone.
-
48. Where is the yellow antilock brake malfunction lamp on a trailer, and what does it mean if it stays lit?
Show answer
Answer D: On the left side, at the front or rear corner, and it means the antilock function may not be working
Trailers carry the yellow lamp on the left side, and a lamp that stays on after the bulb check means the antilock function may be lost even though the normal brakes still work.
-
49. Where on a tire is tread depth measured?
Show answer
Answer C: In a major tread groove, away from any tie bar or wear indicator
Depth is taken in a major groove and away from the raised tie bars and wear indicators, which would give a shallower and misleading reading.
-
50. Why should a large vehicle be accelerated smoothly and gradually?
Show answer
Answer A: Rough acceleration can damage the drivetrain and, on a combination, the coupling
Jerky throttle inputs put shock loads through the driveline and the coupling, which causes mechanical damage over time.